Global Partner for Wiper Products & Market Solutions

Home / All / Spraying Wiper Blades / Good-Value Universal Spraying Wiper

Good-Value Universal Spraying Wiper

Good-Value Universal Spraying Wiper
Good-Value Universal Spraying WiperGood-Value Universal Spraying WiperGood-Value Universal Spraying WiperGood-Value Universal Spraying Wiper
Share
CategoriesSpraying Wiper Blades
BrandSeeVelo
Product SpecificationsJJ-805
Item NumberJJ-805
Size12"-28" (300mm-700mm)
MaterialRubber, plastic, steel wire, iron parts
Temperature Range-40°C to +80°C
PackingCarton: 50 pcs /ctn, inner box optional
Packing ByCarton
Durability300,000 wipe cycles
Detail Information

Good-value Universal Spraying Wiper JJ-805

Washer fluid leaves the blade itself. It travels from the vehicle’s original washer pipe into the wiper, then out through holes moulded along the rubber edge and onto the glass as a mist. The good-value build pairs Teflon-coated rubber with an air deflector and thickened spring steel, and it keeps wiping cleanly even after 300,000 test cycles.

  • JJ-805
  • 12"– 28" / 300 – 700 mm
  • U-hook attachment
  • Teflon-coated rubber
JJ-805 good-value universal spraying wiper blade with U-hook adapter

Four decisions behind the good value

01

Fluid leaves the blade, not the hood

A mist is released along the whole wiping edge instead of from two or three fixed nozzles, so the full sweep of the glass is cleaned in one motion.

02

Teflon-coated rubber rated to 300,000 cycles

The Teflon-coated edge wipes away dust and grime on every corner of the glass in an instant, and it stays durable even after 300,000 test cycles.

03

Air deflector and thickened spring steel

The air deflector keeps the blade planted at speed, while the thicker spring steel and POM plastic parts hold even pressure along the whole edge.

04

Installs like a normal blade

Made for vehicles that use a U-hook attachment. No special tools, no modification to the vehicle, just a normal blade replacement plus one connection to the washer line.

Close-up of the spray holes moulded into the wiper rubber

How the fluid reaches the glass

With a conventional wiper, the jets sit on the hood or the cowl panel. Fluid lands in a few fixed spots, the blade drags it across dry glass, and the result is smearing, wasted fluid and a short moment of poor visibility.

The spraying wiper closes that gap. Fluid runs from the vehicle’s original pipe into the blade and leaves through precisely moulded holes along the rubber, spreading exactly where the rubber meets the glass on every pass.

One blade for every U-hook arm on the road

Tell us your car model, year and arm type and we will confirm the length.

JJ-805 spraying wiper blade mounted on a U-hook wiper arm

Sizes in the JJ-805 range: 12", 14", 16", 18", 20", 22", 24", 26", 28" (300 – 700 mm)

JJ-805 washer connection kit: tubing coil, straight joint, tee joint, mounting clips and cable ties

What arrives with each blade

  • 1.5 m washer tubingMain run from the original pipe
  • 2 × 0.7 m washer tubingOne piece to each blade
  • Straight jointJoins the original pipe to the 1.5 m tube
  • Tee jointSplits the line to the left and right blades
  • Mounting clipsHold the tube along the cowl without rattles
  • Cable tiesFix the hose run for a clean engine-bay finish

Installation

No special tools and no modification to the vehicle. A normal blade replacement plus one connection to the washer line.

Connect to the original pipe

Find the washer pipe, usually on the side of the passenger seat, and join it to the 1.5 m tube with the straight joint.

Split the line

The tee joint sends fluid down the two 0.7 m tubes, one towards each side of the glass.

Mount and connect

Clip the blades onto the U-hook arms and push a 0.7 m tube onto each blade.

JJ-805 spraying wiper installation guide showing the five fitting steps

The five-step fitting sheet supplied with every blade.

Engineering detail

Rubber
Teflon-coated rubber with air deflector
Frame and fittings
Thickened spring steel, POM plastic parts, iron fixings
Durability
Tested to 300,000 wipe cycles
Attachment
U-hook wiper arms, 12"– 28" / 300 – 700 mm
Temperature range
-40°C to +80°C
Packing
Carton: 50 pcs /ctn. The inner box can be selected

Need pricing or a sample?

Tell us the models you serve and the volumes you move most. We will come back with the full specification, the packaging configuration and a quotation.

Review
  • 加载中···
Please send your message to us
*Email
Phone
*Title
*Content
Upload
  • Only supports .rar/.zip/.jpg/.png/.gif/.doc/.xls/.pdf, maximum 20MB.